厂家直销数控液压摆式剪板机QC12Y-4*2500

性能特点：
 本机器采用钢板焊接结构,机身采用有限元分析设计、振动时效消除内应力，使机身稳定、可靠。
◎采用三点支撑滚动导轮，消除支撑间隙，提高剪切精度。
◎刀架剪切角能在一定的范围内调整，可使剪切材料变形量减小到理想状态，又可剪切**厚板料。
◎剪切行程任意调整，提高了工作效率，又可实现分段剪切功能。
◎后挡料设计了手动抬升功能，便于**长板料剪切。
◎墙板内侧设有手动加油泵，操作方便，保证关键部位的润滑。
◎插装式液压系统，减缓油温提升，增强机床运行的可靠性和安全性。
◎标配采用MD-100**系统及PLC控制器，剪切计数、后挡料、剪切角及刀口间隙的调节直观、简单、方便。
◎可选用DAC310、DAC360数控系统以满足更高精度要求的剪切和控制。
 
This machine adopts steel plate welding structure, the fuselage using the finite element analysis and design, Vibratory Stress Relief of internal stress, so that body stable and reliable.
◎Using three-point rolling guide pulley can eliminate the support gap, and increase cutting precision.
◎Shearing angle can be adjusted within a certain range, which can reduce the shearing deformation of sheet metal and can shear much thicker sheet metal.
◎The shearing stroke can be adjusted at will, which raise the working efficiency and realize the function of partition cutting.
◎The backgauge is designed manual lifting function, which is convenient to shear long sheet metal.
◎Inside the wallboard manual petrol pump is installed, which makes operating convenient and lubricating reliable.
◎Plug in hydraulic system can make oil temperature become high slowly, meanwhile it enhance the reliability and safety operation of machine.
◎Standard machine is installed MD-100 dedicated system and PLC controller,Adjustment of shearing counting,back gauge,shearing angle and blade gap is simple and convenient.
◎DAC310 and DAC360 control system is optional,which can meet demand for higher precision of cutting and control.

摆式剪板机维护保养的方法
1、严格按照操作规程进行操作。
2、每次开机前按润滑图表要求定时、**、定量加润滑油，油应清洁无沉淀。
3、机床必须经常保持清洁，未油漆的部分应涂抹防锈油脂。
4、电动机轴承内的润滑漾油要定期更换加注，并经常检查电器部分工作是否正常安全可靠。
5、定期检查链条、手柄、旋钮、按键是否损坏，磨损严重的应及时更换，并报备件补充。
6、定期检查修理开关、保险、手柄、保证其工作可靠。
7、每天下班前10分钟，对机床加油润滑及擦洗清洁机床。
8、严禁非*人员操作该设备，平常必须做到人离机停。


Shears maintenance method
1, strictly follow the operation procedures for operation.
2, every time before the start of the lubrication chart to require the timing, fixed point, quantitative lubricating oil, oil should be clean without precipitation.
3, machine tools must often keep clean, the part of the paint should be coated with rust preventive grease.
4, motor bearing lubrication overflow oil should be changed regularly filling, and always check whether the normal work of safe and reliable electrical parts.
5, regularly check the chain, handle, knob, key press whether damage, wear serious should be replaced, and to spare parts for spare.
6, check the repair switch, insurance, handle, guarantee its work reliably.
10, 7 minutes before work every day, lubrication and cleaning machine tool for machine tools.
8, non designated personnel to operate the device, usually must be done to stop the machine.